Will a stock 68 camaro rear end with locker hold up to 500 or 600 hp?

Question:


Answers:

i have a 81 f150 with an inline 6 and was wondering if i put a 302 would i have to change the bellhousing.?

Is their 12 bolts in the rear end housing cover? If so than YES!! Camaros are light in the rear end so you will get considerable wheel / spin. If it's a 12 bolt than the same forged ring and pinion in it is also in the ground pounding "69" Camaros and Corvettes that had the underrated 427 ci 460 hp with 470+ lbs of torque

---

How do you program keyless entry remote for 2004 Altima ?

nope

---

1993 Volvo 940 Rear Deck Speakers?

you will need a prepared Ford 9 inch :)

---

How much will a Paint Job run me on a 1998 Honda Accord?

if you are talking about 600hp with out NOS then you can weld the tubes, get heavy duty axles and a large tooth ring and pinion then it can handle it, but it is easier to get a Ford 9" or a Chevy 12 bolt

---

my power kord keep shutting off?

With out significant suspension and frame stabilizers the rear end is the least of your worries.
Won't even mention the brake system...whoops....
Just my opinion, I could be wrong.

---

cold air out take?

aint nooooo way. you need that ford 9 inch someone mentioned. but then, if you dont use that 5-600 hp, then the camaro rear will be just fine. but,why have it if you dont use it?

---

1997 cadillac deville electrical problem?

not for long, a ford 9 inch or Dana 60 will still need a bit of work to do it reliably

---

does anyone else LOVE the ford mustangs, especially from the 60's even the shelbys and fastbacks and bosses?

?

---

I have a 97 hyundai elantra - i only get heat when parked i already changed the thermostat?

Nope not at all. Stock rear ends won't even hold up to 400HP. the 10 bolt is a WEAK rearend. you will need to upgrade to a nodular iron Ford 9" rearend. The Ford 9" design when setup properly can handle WELL over 8000 HP

---

I have a 1999 ford windstar and the speakers on the door come an go when I hit a bump etc.?

no,,it wont,,it will rip it right out of it,,know this for sure,i own a repair shop,and i have done a lot of these cars before,and they will rip it out ,you,ll need a good rear end setup for it,,in order for it to hold up good,i do this all the time,and i usually use racing gears ,they hold up better under high horse power,,good luck,hope this help,s.,,have a good x-mas.

---

can a 05 gto with 400 hp beat a 04 cobra or a 06 sti?

ok the dude that said use a for 9inch in a camaro. what dont put ford parts in that car lmao Just weld the gears make sure you have some do it, who has done it before

---

I have a 1992 Toyota 4X4 X-tra cab pickup. I am looking at a new Tacoma. Sport or Off-road Package?

It may for awhile but not very long depending on use.For strenght you should go with a 9 inch ford rear end

---

More Questions & Answers ...

Where can I find free clip art to download for a "Lincoln" automobile logo?

Is 1500 for a 1992 honda accord asking to much?

how many liters is the full tank of a 1989 toyota corolla?

ford ranger repairs?

does anyone know where i can get the wiring diagram for a 2004 lancer es?

can you make the nissan 350z seats to for seater or will it be best not to mess with?

When is the 2008 Civic due in Quebec?

Does anyone own a Subaru Forester XT turbo...have you ever put in a grade lower than premium?

ford mondeo clutch release bearing problems?

I have a 1987 cutlass ciera alternator bracket needs removed how?

This article contents is post by this website user, CarQnA.com doesn't promise its accuracy.