What can I do for a moldy back seat in my car?

Question:
My back window leaks condensation onto the seat and now it's getting moldy. Does anyone know of anything that I can used to reduce the dampness and get rid of the mold?

Answers:

Help me plz..?

First take care of the condensation problem. You are using the "fresh" air mode on your heater, correct? You should be, and once in awhile use your AC with the heat selector on HOT. This gets rid of the condensation. If you are using the "recycle" mode, it is much like sitting in a closed mayonase jar. To get the back seat dry, you either need to remove the seat and take it inside to dry for a couple of days, or put the car in a garage and open the doors and have a fan blow air across the back seat. The best way is to remove the seat, squeeze as much water out and then let it air dry. To remove the mold, you will need to mix 2 tablespoons of bleach with one gallon water, put in a sprayer and MIST the seat, carefull not to soak the fabric. Then when dry, mist with Fabreeze to give a fresh smell.

My 2000 Chevy Van is overheating.?

Try to use silicone on the window seal. IF you don't stop the leak it will keep creating mold. Walmart makes a carpet cleaner that is similar to resolve in an aerosol can. It works very well on upholstry and sells for .99 a can.

Why Am I having diffuculties with my car starting after I changed My Spark Plugs?

Take the seat out of the car, take it to a car wash, and clean it. Then set it out in the sun to dry for about 48 hours. While it is drying, take your car to a glass shop and have them repair or replace the seal around your back window. ($100 or less) You may also need to clean up under the seat and in the trunk. Get it cleaned and fixed fast, mold can make you sick.

idle in car engine..?

get someone to sit back there or spray bleach on it

Can anyone help? Throttle Position Sensor (TPS)?

Uh yea, fixing the leak will greatly reduce dampness. Try silicone around your window seal.

How do I increase gas mileage of my Toyota Camry?


To get the mold off, you are going to have to get the cars interior completely dry first. Then the majority of it should vacuum right up. Lysol makes a good mold killing spray to.

Can you help diagnose my car's weird cooling system issue?

Scrub the mold out as much as possible. Try to find and seal the leak. Then put dehydrating crystals in the back. They will gather any excess moisture to keep the mold from coming back.

How would I take out a key the broke in my door?

For me, Lysol has worked really well on all of that little yucky stuff. Dilluted bleach works well on plastic however, it usually turns anything it touches white.

Weather sensitive ABS light?

seal the windows with silicon... next take out the back seats and clean everything under the seats with clorox whipes + diluted bleach.. this will kill any mold there.... use a diluted bleach spray to kill the mold on the seats and clean it thoroughly...
mold can make people sick and constant inhalation of the fumes could kill you depending on how long the mold has been there... entire homes get torn down because of the same mold in your car, in peoples homes. Try driving with the windows down until you fix your problem.. or atleast crack the back 2 windows..
More Questions & Answers ...

  • how can i disconnect rover metro immobillisors on a 114gsi?
  • Why is my air filter still clean?
  • mechianic needed!!!?
  • how do i lubricate front anti lock brake sensors /98 g. m. silverado?
  • why oil price going down but gasoline not going down so fast?
  • how much does it cost to replace front brakes?
  • Adding tranny fluid to a manual?
  • Saab 9-5 owner has question about Alarm System Malfunction - any advice?
  • Is it hard to change the steering column in a Ford Windstar?
  • i have a 1993 vauxhall 3 door corsa and need a new parcel shelf will only 1993 shelves fit?

    • This article contents is post by this website user, CarQnA.com doesn't promise its accuracy.


    Copyright 2006-2008-2007 CarQnA.com. All Rights Reserved.