Question:
Answers:
How come my oil turns black after just a week?
Service and RepairNotes
INSPECTION
Where exactly is the PCV valve located on a 89 Mazda B2200 pickup?
Raise vehicle and support the frame.
Remove the front wheel.
how many times can you paint a car?
Help, what does it mean when my brake light comes on?
Look through side of caliper to visually check pad thickness. Also check to see if wear indicator is touching the disc assembly. Always replace pads if wear indicator touches rotor. NOTICE: Hydraulic fluid will damage paint. If fluid gets on a painted surface, wipe off immediately.
REMOVAL
how much would it cost to get an 1994 integra painted tangerine orange?
I need to know the paint code for my Metallic Silver Citroen saxo\?
Touch-up Paint for my car. Best way?
Remove the two caliper assembly bolts and pull caliper from disc.
how do i take my steering wheel off?
Why am I getting a code reading for a part that is not installed on my 1993 GMC Sonoma pickup ?
Remove the brake pads from the adapter.
Is the method of repairing puctured tyre same for tubeless tyre as with tubed tyre?
Engine on my car wont stop, why?
Remove the two adapter mounting bolts and then remove the adapter.
can someone please tell me whats wrong with my car?
1997 Honda Accord Auto Transmission down-shifting hard and seems to lurch on acceleration...?
Remove the two screws and then remove the disc assembly.
INSPECTION
Check for oil or grease on the pads or on the disc assembly.
why has the fuel economy on my van dropped all of a sudden?
will a 2003 chevy 2500 front bumper fit a 2002 chevy 1500 or 2500?
Check pad lining thickness. If below minimum, replace pad. Minimum Thickness: 0.08 inch (2.0 mm) New Thickness: 0.37 inch (9.5 mm)
Visually check disc for damage or wear.
Measure disc thickness. If below minimum, replace disc assembly. Standard: 0.94 inch (24 mm) Minimum: .088 inch (22.4 mm)
automatic transmission noise i hear when it change gears?
Why do people put towels and shirts in the window of their vehicle if it's broken down?
Visually check the piston seal for holes, tears, or other damage. Replace using piston repair kit.
INSTALLATION
Well a engine from a 2003 tahoe z71 fit in my 97 tahoe 4x4?
How do you compress springs on a Macpherson strut.?
Place disc assembly on front axle and install the disc screws. Check the disc runout from the outer surface. Runout: 0.004 inch (0.10 mm) at 4.7 inch (12 cm) from disc center
Check that anti-rattle clip is on the adapter and then install the adapter and bolts. Tighten the bolts to 17 ft. lbs. (23.5 Nm)
Place brake pads on adapter.
how to fix my E100 electric scooter?
If the head gasket on my 1998 Chevey malibu is bad, can I replace that myself?
Using a C-clamp or similar device, push the caliper piston into the caliper.
Place the caliper assembly in position on the disc assembly. Tighten the bolts to 72 ft. lbs. (98 Nm)
The heater isn't working properly in my 1996 Dodge Intrepid?
my oil light on me car comes on now and again but the oil level is fine,wots the prob? help!?
Install the tire and .
Pump the brake pedal three times and then check brake movement while rotating the tire.
How do I remove acrylic craft paint from my car?
Wheel Bearings....where are my car people!?
need to know where i can get a manifold intake for a 97 cougar?
© 2007 ALLDATA LLC. All rights reserved.
Terms of Use
The ventilation system in my car is broken?
you jack it up ,make sure its safe,and remove the front wheels,and remove the caliper bolts and pull the calipers of of it,press them in real slowly with a c-clamp,and check the rotors to see if there bad ,if there alright put the new shoes in place and replace the calipers on it,and replace the bolts,tighten them good ,install the wheels ,and test drive it,and your done,good luck,i hope this help,s.More Questions & Answers ...
This article contents is post by this website user, CarQnA.com doesn't promise its accuracy.